Three panel cover configuration - Maximum length over 102 up to 144 inches *

View example
A). The center panel will be flat and not tapering. For example, if your order is for a 4-2 cover, the center panel will be 4 inches thick and flat
B). Both end panels will taper from the center panel thickness out, dropping 2 inches to the end of the cover
C). One end panel will be attached to the center panel with the standard cover hinge/fold
D). The center panel has a 4 inch flap to cover the joint with the panel that is not attached, so rain cannot get in
E). The tie down straps will be located on each end of the center panel, and on all 3 sides of the end panels

• I confirm my agreement with the three panel cover configuration explained above

Cover thickness selection *

REQUIRED: Select your cover thickness here. Thicker covers insulate better.

• 4" thick center panel, end panels taper 4" to 2" +$383.88
• 5" thick center panel, end panels taper 5" to 3" +$440.88
• 6" thick center panel, end panels taper 6" to 4" +$477.88

Hot tub cover shape *

Preview All Shape Choices

-- Please Select --Square with rounded corners - Requires only A, B and C dimensions Square - Requires only A and B dimensions Square 4 cut corners - Requires only A, B and C dimensions Rectangle - Requires only A and B dimensions Rectangle rounded corners - Requires only A, B and C dimensions Rectangle 4 cut corners - Requires only A, B and C dimensions Single cut corner - Requires A, B, C, D and E dimensions Two cut corners - Requires A, B, C, D and E dimensions Round - Requires only A dimension Hexagon (6 equal sides) - Requires only A, B and C dimensions Octagon (8 equal sides) - Requires only A, B and C dimensions

Dimension A (in inches) Typically the longer side *

Measure the overall length, ignoring the corners and entering fractions such as 88 1/2 as 88.5 Measuring your cover    Measuring your hot tub

Dimension B (in inches)

Measure the overall length, ignoring the corners and entering fractions such as 88 1/2 as 88.5 Measuring your cover    Measuring your hot tub

Dimension C (in inches)

Rounded corners? Help Me    Photo with Measuring Tape    Video Guide    Calculator    Cut corners? Photo with Measuring Tape

Dimension D (in inches)

Measure as shown by the line in the illustration above Measuring your cover

Dimension E (in inches)

Measure as shown by the line in the illustration above Measuring your cover

Vinyl color selection *

View all colors

• Light Gray
• Gray
• Charcoal
• Black
• Light Blue
• Navy
• Teal
• Hunter Green
• Burgundy
• Sand
• Tan
• Brown
• Old Teak
• Walnut

Skirt (flap) length *

See how to measure

-- Please Select --No skirt 1 inch 1.5 inches 2 inches 2.5 inches 3 inches 3.5 inches 4 inches 4.5 inches 5 inches 5.5 inches 6 inches 6.5 inches +$15.007 inches +$15.007.5 inches +$15.008 inches +$15.008.5 inches +$15.009 inches +$15.009.5 inches +$15.0010 inches +$15.00

Additional insulation *

To add maximum insulation, select the Eco Upgrade Bundle below to add the Eco soft bottom and the Eco extra steam stoppers

• Standard: Steam stopper pillows View
• Upgrade: Full hinge seal - additional insulation seals under the fold View +$19.00
• Eco Upgrade Bundle: A-Full hinge seal; B-Additional heat blockers at each end of the fold; C-Padded cushion where cover sits on tub, seals in the heat; D-Adds 4 tie down straps (8 total) REQUIRES 2 straps/side replaces locations from above; Adds R-16.4 +$65.00

Extend the life of your cover 12-18 months - 82% of covers fail from waterlogging *

• Standard: Vapor Barrier
• Upgrade: Double Thick Vapor Barrier View +$20.00
• Upgrade: Tuff Stuff Barrier – Double Thick & More Durable View +$27.00

Increase cover strength with more dense foam cores *

Add strength to support snow, animals, etc. so the foam does not break View

• Standard 1 pound - Shear strength 18-22 psi (Estimated 4-2 taper static load limit - 190 pounds)
• Deluxe 1.5 pound - Shear strength 26-32 psi (Estimated 4-2 taper static load limit - 270 pounds) +$67.50
• Ultra Deluxe 2 pound - Shear strength 33-37 psi (Estimated 4-2 taper static load limit - 370 pounds) +$98.75

Split corner skirts help prevent the skirt folding under the cover and leaking heat *

• Standard: Full corner skirt
• Upgrade: Split corner skirt View +$24.00

Reinforce the fold/hinge for additional strength *

Add strapping when a cover lifter is used Prevent this!

• Standard: No strapping sewn into the fold
• Upgrade: Strengthen the fold/hinge View +$18.00

Add internal hardware so Hot Spring lifters can attach to the cover *

• Standard: No internal cover lifter attachment hardware
• Upgrade: Add adapter hardware (Info) +$48.50

Are corner speaker pockets required? *

See an example

• The hot tub does not have any raised speakers
• 2 corner speaker pockets are required +$52.00
• 4 corner speaker pockets are required +$104.00

For 2 speaker hot tubs, provide their locations *

• Both speakers are on the same side of the fold
• The fold runs between the speakers

Comfy & matching pillows with strap to sand bag to hold the pillow on the lip *

• No pillow(s) - View
• 1 Pillow +$26.00
• 2 Pillows +$48.00
• 3 Pillows +$68.00
• 4 Pillows +$87.00

How did you find BeyondNice? *

-- Please Select --Amazon Become.com Bing search BizRate Business card Craigslist Facebook Google Advertisement Google Search HotTubCoverPros.com LinkedIn Nextag Other PriceGrabber Pronto Read Article Referral Returning Client Sears Shopping.com Shopzilla Smarter Twitter Yahoo search YouTube

If other, please explain: *

* Required Fields